The Often Unknown Benefits Of Rolls Royce Key For Sale > 자유게시판

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why Your Rolls Royce Phantom Key Fob Isn't Locking Or Unlocking

The Rolls-Royce Phantom is unmatched in terms of sheer luxury. It's bigger and heavier, as well as more luxurious than many SUVs.

A defective keyfob may make it difficult to operate your Phantom. There are steps you can take to fix it.

Battery Replacement

The key fob is powered by an e-cigarette size battery. The remote key will not work if the battery inside dies. A dead battery in the key is the most frequent reason for a Rolls-Royce Phantom remote key not locking or unlocking. It is also possible that the key fob won't function as it should if the battery terminals and ground connection are corroded.

The process of replacing the key is fairly simple. Make sure the key is clean and dry. You don't have to introduce moisture to the battery. After that, press the release button on the side of the fob to remove the mechanical key. Next you will need a screwdriver to open the key fob cover and remove the old battery. Replace the battery with a brand new one. Make sure that the positive (+) face is facing upwards. Secure the cover by snapping it in place.

The Phantom key fob is fitted with rubber seals in order to prevent water from reaching the chip. However, if the key is submerged in water for a long period of time, for example submerging it in the ocean or swimming pool, Rolls Royce Phantom Key it could damage the chip. A brief exposure to splashes of water is acceptable, however prolonged immersion in water may cause the circuit board to fail. In this scenario, replacing the battery is the best solution.

Water Damage

The key fob may be waterproof but a run in the pool or soaking in the washing machine can still cause problems. The circuit board could get shorted and corrosion or rust may begin to set in faster. In extreme situations batteries can explode or even die.

You can stop this from happening by removing the fob from the water as soon as it is possible. But, you must also replace the battery. Make sure you use the identical button cell battery as the original one and you can get a replacement of the same size and voltage. Clean the electronic component using alcohol or an electronic cleaner prior to installing it.

After replacing the battery, turn your Phantom on and press each button. If any don't work you'll need to tear it apart and dry it out before you can use it again.

The most efficient method to accomplish this is to put the fob into small containers filled with rice. The rice will absorb any moisture that may be leaking into the fob. You can also make use of a hairdryer, or a heat gun to dry the circuit boards and the inside of the fob. Just be sure to avoid using a microwave as the circuitry on the key fob's board could be damaged. After drying then reassemble it and test it again.

Troubleshooting

It is a traumatic experience to lose your keys. In the ideal case the keys are found exactly where you left them (Parent Logic insists they always appear in "the last spot you looked at" however it's not something you can argue about). However, if your key fob doesn't turn on and isn't responding to any of your commands, it's not so simple.

First, check the coin battery Dead batteries cause remote key fobs to fail most of the time. A dying battery will begin to display signs of degradation such as a decreased range until it ceases to function. Make sure that you replace the battery using one with the same voltage, size and specification as it is crucial that the replacement is done correctly to avoid damaging the electronics.

The chip inside the key fob may be damaged. This can happen when the key fob is dropped on a hard surface, or when it comes in contact with water. In this situation, remove the chip from the key fob and clean it with isopropyl or electronic cleaner.

In the end, it's possible that the receiver module in your Phantom has developed fault. This could be due to a number reasons, including signal interference, a dead 12-volt battery or a key that is not paired which requires reprogramming.

Reprogramming

A Rolls Royce Phantom key fob that suddenly stops working could indicate a problem with your receiver module, the tiny unit located in the boot that receives radio frequency signals from your remote key fobs. If the key fob stopped working after you dropped it on the floor or if one of the keys ceases to respond to your commands, it might be time to contact an auto locksmith for reprogramming.

The key fob has rubber seals that prevent water from damaging the chip inside. However prolonged exposure to water can damage these seals. The submersion of a key into an in-ground pool or bath could cause damage. However, a drop of ocean water at the beach is much worse because of the high-conductive saltwater that is naturally present in the.

You can still re-program your Phantom keyfob in case it has been damaged by water.

Close all doors, with the exception of the driver's, and then take the car into the garage. Then, put your car's key into the ignition and switch it to "ON" position. Some models will sound an alarm when you enter the program mode. In the end press and hold both the "UNLOCK" and "PANIC" buttons on your new key fob for a couple of seconds before taking them off. Your car will then chime to confirm that you're in program mode and that your key fob has successfully connected to your car.